PPTP session helper for PPTP traffic (pptp)
The PPTP session help supports port address translation (PAT) for PPTP traffic. PPTP provides IP security at the Network Layer. PPTP consists of a control session and a data tunnel. The control session runs over TCP and helps in establishing and disconnecting the data tunnel. The data tunnel handles encapsulated Point-to-Point Protocol (PPP) packets carried over IP.
To accept PPTP sessions that pass through the FortiGate unit you must add a security policy with service set to any or to the PPTP pre-defined service (which listens on IP port 47 and TCP port 1723). The pptp session helper listens on TCP port 1723.
PPTP uses TCP port 1723 for control sessions and Generic Routing Encapsulation (GRE) (IP protocol 47) for tunneling the encapsulated PPP data. The GRE traffic carries no port number, making it difficult to distinguish between two clients with the same public IP address. PPTP uses the source IP address and the Call ID field in the GRE header to identify a tunnel. When multiple clients sharing the same IP address establish tunnels with the same PPTP server, they may get the same Call ID. The call ID value can be translated in both the control message and the data traffic, but only when the client is in a private network and the server is in a public network.
PPTP clients can either directly connect to the Internet or dial into a network access server to reach the Internet. A FortiGate unit that protects PPTP clients can translate the clients’ private IP addresses to a pool of public IP addresses using NAT port translation (NAT-PT). Because the GRE traffic carries no port number for address translation, the pptp session helper treats the Call ID field as a port number as a way of distinguishing multiple clients.
After the PPTP establishing a TCP connection with the PPTP server, the client sends a start control connection request message to establish a control connection. The server replies with a start control connection reply message. The client then sends a request to establish a call and sends an outgoing call request message. FortiOS assigns a Call ID (bytes 12-13 of the control message) that is unique to each PPTP tunnel. The server replies with an outgoing call reply message that carries its own Call ID in bytes 12-13 and the client’s call ID in bytes 14-15. The pptp session helper parses the control connection messages for the Call ID to identify the call to which a specific PPP packet belongs. The session helper also identifies an outgoing call request message using the control message type field (bytes 8-9) with the value 7. When the session helper receives this message, it parses the control message for the call ID field (bytes 12-13). FortiOS translates the call ID so that it is unique across multiple calls from the same translated client IP. After receiving outgoing call response message, the session helper holds this message and opens a port that accepts GRE traffic that the PPTP server sends. An outgoing call request message contains the following parts:
- The protocol used for the outgoing call request message (usually GRE)
- Source IP address (PPTP server IP)
- Destination IP address (translated client IP)
- Destination port number (translated client call ID)
The session helper identifies an outgoing call reply message using the control message type field (bytes 8-9) with the value 8. The session helper parses these control messages for the call ID field (bytes 12-13) and the client’s call ID (bytes 14-15). The session helper then uses the client’s call ID value to find the mapping created for the other direction, and then opens a pinhole to accept the GRE traffic that the client sends.
An outgoing call reply message contains the following parts:
- Protocol used for the outgoing call reply message (usually GRE)
- Source IP address (PPTP client IP)
- Destination IP address (PPTP server IP)
- Destination port number (PPTP server Call ID)
Each port that the session opens creates a session for data traffic arriving in that direction. The session helper opens the following two data sessions for each tunnel:
- Traffic from the PPTP client to the server, using the server’s call ID as the destination port
- Traffic from the PPTP server to the client, using the client’s translated call ID as the destination port
The default timeout value of the control connection is 30 minutes. The session helper closes the pinhole when the data session exceeds the timeout value or is idle for an extended period.
Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!
Don't Forget To visit the YouTube Channel for the latest Fortinet Training Videos and Question / Answer sessions!
- FortinetGuru YouTube Channel
- FortiSwitch Training Videos