Category Archives: FortiOS 6

Configuring IP pools

Leave a reply

Configuring IP pools

An IP pool is essentially one in which the IP address that is assigned to the sending computer is not known until the session is created, therefore at the very least it will have to be a pool of at least 2 potential addresses. A quick example would be an IP pool for users of a VPN. IP pools are based upon the version of IP determined by the interface that they are associated with so as expected there are two types of IP pools that can be configured:

l “Creating a IPv4 pool” on page 243 l “Creating a IPv6 pool” on page 247

Because of the differences in the configuration for the two types of pools, instructions for configuring them will be done separately.

Creating a IPv4 pool

  1. Go to Policy & Objects > IP Pools.
  2. Select Create New.
  3. In the IP Pool Type field choose IPv4 Pool
  4. Enter a name in the Name field for the new service Include any description you would like in the Comments field
  5. In the Type field choose between:

l Overload l One-to-One l Fixed Port Range l Port Block Allocation

At this point the configurations can start to differ based on the type of type of pool.

For more information on the different types of IP pools, check IP Pools in the Concepts section.

Overload

  1. For the External IP Range fields, enter the lowest and highest addresses in the range. If you only want a single address used, enter the same address in both fields.
  2. Enable the ARP Reply field by making sure there is a check in the box
  3. Select OK
Overload example for GUI

In this example, the Sales team needs to connect to an Application Service Provider that does the accounting for the company. As a security measure, the ASP only accepts traffic from a white list of IP addresses. There is 1 public IP address of the company on that list.The Sales team consists of 40 people, so they need to share.The external interface is wan1.

Field Value
IP Pool Type IPv4 Pool
Name Sales_Team
Comments For the Sales team to use to connect to the Accounting ASP
Type Overload (This is the default)
External IP Range 10.23.56.20 – 10.23.56.20
ARP Reply enabled
Overload example for CLI

config firewall ippool edit Sales_Team set comments “For the Sales team to use to connect to the Accounting ASP”

set type overload set startip 10.23.56.20 set endip 10.23.56.20 set arp-reply enable set arp-intf wan1 end

One-to-one

  1. For the External IP Range fields, enter the lowest and highest addresses in the range. If you only want a single address used, enter the same address in both fields.
  2. Enable the ARP Reply field by making sure there is a check in the box.
  3. Select OK
One-to-one example for GUI

In this example, the external IP address of the mail server is part of a range assigned to the company but not the one that is assigned to the Internet facing interface. A VIP has been set up but in order to properly resolve Reverse DNS lookups the mail server always has to use a specific IP address.The external interface is wan1.

Field Value
IP Pool Type IPv4 Pool
Name Mail-Server
Comments So the correct IP address is resolved on Reverse DNS look ups of the mail server.
Type One-to-one
External IP Range 10.23.56.21 – 10.23.56.21
ARP Reply enabled
One-to-one example for CLI

config firewall ippool edit Mail-Server set comments “So the the correct IP address is resolved on reverse DNS look ups of the mail server.”

set type one-to-one set startip 10.23.56.21 set endip 10.23.56.21 set arp-reply enable set arp-intf wan1 end

Fixed port range

  1. For the External IP Range fields, enter the lowest and highest addresses in the range. If you only want a single address used, enter the same address in both fields.
  2. Fort the Internal IP Range fields, enter the lowest and highest addresses in the range.
  3. Enable the ARP Reply field by making sure there is a check in the box
  4. Select OK
Fixed port range example for GUI

In this example, the company has a range of 10 IP address that they want to be used by employees on a specific subnet for NATing.The external interface is wan1.

Field Value
IP Pool Type IPv4 Pool
Name IPPool-3
Comments IP range to be used by outgoing traffic
Type Fixed Port Range
External IP Range 10.23.56.22 – 10.23.56.31
Internal IP Range 192.168.23.1 – 192.168.23.254
ARP Reply enabled
Fixed port range example for CLI

config firewall ippool edit IPPool-3 set comments “So the the correct IP address is resolved on reverse DNS look ups of the mail server.”

set type fixed-port-range set startip 10.23.56.22 set endip 10.23.56.31 set source-startip 192.168.23.1 set source-endip 192.168.23.254 set arp-reply enable set arp-intf wan1 end

Port block allocation

  1. For the External IP Range fields, enter the lowest and highest addresses in the range. If you only want a single address used, enter the same address in both fields.
  2. In the Block Size field, either type in the value or use the up or down arrows to set the value of the block size.
  3. In the Blocks Per User field, either type in the value or use the up or down arrows to set the value for the number of blocks per user.
  4. Enable the ARP Reply field by making sure there is a check in the box
  5. Select OK
Port block allocation timeout

The port block allocation timeout value is configurable. The setting is found in the CLI.

The option pba-timeout has been added to the firewall ip pool configuration. The availability of this option is dependent on the type option being set to port-block-allocation. The timeout value is measured in seconds and is an integer between 3 and 300, with the default being 30.

Syntax:

config firewall ippool

edit <name of PBA pool> set type port-block-allocation set pba-timeout <integer> end

Port block allocation example for GUI

In this example, an small ISP is setting up NATing for its clients, but to be fair it is putting some restrictions on the number of connections each client can have so that no one hogs all of the possible ports and addresses.The external interface is port12.

Field Value
IP Pool Type IPv4 Pool
Name Client-IPPool
Comments IP Pool for clients to access the Internet
Type Port Block Allocation
External IP Range 10.23.75.5 – 10.23.75.200
Block Size 64
Blocks Per User 8
ARP Reply enabled
Port block allocation example for CLI

config firewall ippool edit Client-IPPool set comments “IP Pool for clients to access the Internet”

set type port-block-allocation set startip 10.23.75.5 set endip 10.23.75.200 set block-size 64 set num-blocks-per-user 8 set permit-any-host disable set arp-intf wan1 set arp-reply enableset arp-intf port12

end

Creating a IPv6 pool

  1. Go to Policy & Objects > IP Pools.
  2. Select Create New.
  3. In the IP Pool Type field choose IPv6 Pool
  4. Enter a name in the Name field for the new service
  5. Include any description you would like in the Comments field
  6. For the External IP Range fields, enter the lowest and highest addresses in the range.

IPv6 example for GUI

In this example, there is a similar situation to the One-to-one example earlier.There is a mail server that needs to be resolved to a specific IP address in Reverse DNS look-ups. The difference in this case is the company is an early adopter of IPv6 connectivity to the Internet.

Field Value
IP Pool Type IPv6 Pool
Name Mail-svr-ipv6
Comments Registered IPv6 address for mail server
External IP Range fd2f:50ec:cdea:0663::1025 – fd2f:50ec:cdea:0663::1025

Port block allocation example for CLI

config firewall ippool6 edit Mail-svr-ipv6 set comments “Registered IPv6 address for mail server”

set startip fd2f:50ec:cdea:663::102 set endip fd2f:50ec:cdea:663::1025 end

Creating NAT46 IP pool and multiple (secondary) NAT64 prefixes

Policies that translate between IPv4 and IPv6 can use IPv4 address pools or IPv6 prefixes to be used in the policies, giving more options to the configuration of addresses.

NAT46

For using the ippool in NAT46 policies, first enable the use of ippools and then set the names of the ippool(s).

config firewall policy46 edit 1 set uuid e9c6ca3e-72ea-51e7-554a-1185693d03eb

set srcintf “wan1” set dstintf “internal7” set srcaddr “external-net4” set dstaddr “internal-vip46” set action accept set schedule “always”

 

set service “ALL” set ippool enable set poolname “intit-pool6” end

NAT64

In order to use these options in the NAT64 firewall policies the new settingssecondary-prefix status and secondary-prefix options have to be configured as in the example below.

config system nat64 set nat64-prefix 2001::/96 set secondary-prefix enable config secondary-prefix edit 1 set nat64-prefix 2002::/94

next

edit 2 set nat64-prefix 2003::/95

end end


Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!

Virtual IP groups

5 Replies

Virtual IP groups

Just like other address, Virtual IP addresses can be organized into groups for ease of administration. If you have multiple virtual IPs that are likely to be associated to common firewall policies rather than add them individually to each of the policies you can add the instead. That way, if the members of the group change then any changes made to the group will propagate to all of the policies using that group.

When using a Virtual IP address group the firewall policy will take into account all of the configured parameters of the Virtual IPs: IP addresses, Ports and port types.

Creating a virtual IP group

  1. Go to Policy & Objects > Virtual IPs.
  2. Select Create New. A drop down menu is displayed. Select Virtual IP Group.
  3. Select the Type for VIP group you wish to create. The options available are:

l IPv4 – IPv4 on both sides of the FortiGate Unit. l IPv6 – IPv6 on both sides of the FortiGate Unit. l NAT46 – Going from an IPv4 Network to an IPv6 Network. l NAT64 – Going from an IPv6 Network to an IPv4 Network.

Which is chosen will depend on which of the IP version networks is on the external interface of the FortiGate unit and which is on the internal interface. The options will be:

  1. Enter a unique identifier for the group in the Name
  2. Enter any additional information in the Comments
  3. If you wish, use the Change link to change the Color of icons in the GUI. There are 32 color options.
  4. If the Type is IPv4, the Interface field will be available. Use the drop-down menu to select the interface if all of the VIPs are on the same interface. If any of the VIPS are on different interfaces or if any of them are associated with the “any” option, choose the any option for the group.
  5. Select anywhere in the Members field to bring forth the pane of potential members for selection to the group.
  6. Press

Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!

Dynamic VIP according to DNS translation

Leave a reply

Dynamic VIP according to DNS translation

When a dynamic virtual IP is used in a policy, the dynamic DNS translation table is installed along with the dynamic NAT translation table into the kernel. All matched DNS responses will be translated and recorded regardless if they hit the policy. When a client request hits the policy, dynamic NAT translation will occur if it matches a record, otherwise the traffic will be blocked.

Syntax

config firewall vip edit “1” set type dns-translation set extip 192.168.0.1-192.168.0.100

set extintf “dmz” set dns-mapping-ttl 604800 set mappedip “3.3.3.0/24” “4.0.0.0/24” end end

 


Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!

FQDN in VIPs

2 Replies

FQDN in VIPs

Instead of mapping to an IP address a VIP can use a FQDN(Fully Qualified Domain Name). This has to be configured in the CLI and the FQDN must be an address object that is already configured in the address listing.

The syntax for using a FQDN is:

config firewall vip edit <VIP id> set type fqdn

set mappped-addr <FQDN address object> end


Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!

Creating a virtual IP

1 Reply

Creating a virtual IP

  1. Go to Policy & Objects > Virtual IPs.
  2. Select Create New. A drop down menu is displayed. Select Virtual IP.
  3. From the VIP Type options, choose an applicable type based on the IP addressing involved. Which is chosen will depend on which of the IP version networks is on the external interface of the FortiGate unit and which is on the internal interface.

The available options are:

  • IPv4 – IPv4 on both sides of the FortiGate Unit. l IPv6 – IPv6 on both sides of the FortiGate Unit. l NAT46 – Going from an IPv4 Network to an IPv6 Network.
  • NAT64 – Going from an IPv6 Network to an IPv4 Network.
  1. In the Name field, input a unique identifier for the Virtual IP.
  2. Input any additional information in the Comments
  3. The Color of the icons that represent the object in the GUI can be changed by clicking on the [Change] link and choosing from the 32 colors.

Because the configuration differs slightly for each type the next steps will be under a separate heading based on the type of the VIP

Configuring a VIP for IPv4

In the Network section:

  1. If an IPv4 type of Virtual IP, select the Interface

Using the drop down menu for the Interface Field, choose the incoming interface for the traffic.

The IPv4 VIP Type is the only one that uses this field. This is a legacy function from previous versions so that they can be upgraded without complicated reconfiguration. The External IP address, which is a required field, tells the unit which interface to use so it is perfectly acceptable to choose “any” as the interface. In some configurations, if the Interface field is not set to “any” the Virtual IP object will not one of the displayed options when choosing a destination address.

  1. Configure the External IP Address/Range.

There are two fields. If there is a single IP address, use that address in both fields. This will be the address on the outside of the network that is usually the public address of the server. The format of the address will depend on the VIP Type option that was selected.

  1. Configure the Mapped IP Address/Range. This will be the address that the traffic is being directed to.

There are two fields. If there is a single IP address, use that address in both fields. The format of the address will depend on the VIP Type option that was selected. In the Optional Filters

  1. Disable/Enable the Optional Filters.

If only specific IP addresses and/or services are allowed to be the source for traffic using the VIP, enable the Optional Filters.

  1. To specify an allowed address enter the value in the field labeled Source Address. The value can be formatted in three different ways.

l Source IP – Use the standard format for a single IP address l Range – Enter the first and last members of the range l Subnet – Enter the IP address of the broadcast address for the subnet.

To add additional addresses, click on the “+” below the last field with an address. To subtract an address, click on the “X” next to the field you wish to delete.

  1. To specify an allowed Service, toggle the Services option to enabled. Set the Services parameter by selecting the field with the “+” in the field. This will slide a window out from the right. Single or multiple options can be selected by highlighting the services wanted, unless the ALL option is chosen, in which case it will be the only option. For more information on services, check the Firewall Objects section called Services and TCP ports.
  2. Disable/Enable Port Forwarding. If only the traffic for a specific port or port range is being forwarded, enable this setting.
  3. Select the Protocol from l TCP l UDP l SCTP l ICMP
  4. Configure the External Service Port. This is the port(s) on the external interface of the FortiGate (the destination port in the header of the packets). The first field is for the first port in the range the second is for the last port in the range. As you enter a value in the first field, the second field will auto populate with the same number, working on the premise that a single port is common. Just edit the second field to extend the range.
  5. Configure the setting Map to Port.This will be the listening port on the device located on the internal side of the network. It does not have to be the same as the External Service Port. The first field is for the first port in the range the second is for the last port in the range. As you enter a value in the first field, the second field will auto populate with the same number, working on the premise that a single port is common. Just edit the second field to extend the range.
  6. Press

Example

This example is for a VIP that is being used to direct traffic from the external IP address to a web server on the internal network. The web server is for company use only. The company’s public facing web server already used port 80 and there is only one IP external IP address so the traffic for this server is being listened for on port 8080 of the external interface and being sent to port 80 on the internal host.

Field Value
VIP Type IPv4
Name Internal_Webserver
Comments Web server with Collaboration tools for Corporate employees
Interface Any
External IP

Address/Range

 172.13.100.27 <this would normally be a public IP address>
Mapped IP

Address/Range

 192.168.34.150
Optional Filters enabled
Source Address

Filter

 <list of IP addresses of remote users>
Services enabled with HTTP in the list
Port Forwarding enabled
Map to Port 80 – 80

Configuring a VIP for IPv6

In the Network section:

  1. Configure the External IP Address/Range.

There are two fields. If there is a single IP address, use that address in both fields. This will be the address on the outside of the network that is usually the public address of the server. Enter the address in the standard IPv6 format.

  1. Configure the Mapped IP Address/Range. This will be the address that the traffic is being directed to.

There are two fields. If there is a single IP address, use that address in both fields. Enter the address in the standard IPv6 format.

In the Optional Filters

  1. Disable/Enable the Optional Filters.

If only specific IP addresses and/or services are allowed to be the source for traffic using the VIP, enable the Optional Filters.

  1. To specify an allowed address enter the value in the field labeled Source Address. The value can be formatted in three different ways.

l Source IP – Use the standard format for a single IP address l Range – Enter the first and last members of the range l Subnet – Enter the IP address of the broadcast address for the subnet.

To add additional addresses, click on the “+” below the last field with an address. To subtract an address, click on the “X” next to the field you wish to delete.

  1. Disable/Enable Port Forwarding. If only the traffic for a specific port or port range is being forwarded, enable this setting.
  2. Select the Protocol from l TCP l UDP l SCTP
  3. Configure the External Service Port. This is the port(s) on the external interface of the FortiGate (the destination port in the header of the packets). The first field is for the first port in the range the second is for the last port in the range. As you enter a value in the first field, the second field will auto populate with the same number, working on the premise that a single port is common. Just edit the second field to extend the range.
  4. Configure the setting Map to Port.This will be the listening port on the device located on the internal side of the network. It does not have to be the same as the External Service Port. The first field is for the first port in the range the second is for the last port in the range. As you enter a value in the first field, the second field will auto populate with the same number, working on the premise that a single port is common. Just edit the second field to extend the range.
  5. Press

Configuring a VIP for NAT46

In the Network section:

  1. Configure the External IP Address/Range.

There are two fields. If there is a single IP address, use that address in both fields. This will be the address on the outside of the network that is usually the public address of the server. Enter the address in the standard IPv4 format.

  1. Configure the Mapped IP Address/Range. This will be the address that the traffic is being directed to.

There are two fields. If there is a single IP address, use that address in both fields. Enter the address in the standard IPv6 format.

In the Optional Filters

  1. Disable/Enable the Optional Filters.

If only specific IP addresses and/or services are allowed to be the source for traffic using the VIP, enable the Optional Filters.

  1. To specify an allowed address enter the value in the field labeled Source Address. The value can be formatted in three different ways.

l Source IP – Use the standard format for a single IP address l Range – Enter the first and last members of the range l Subnet – Enter the IP address of the broadcast address for the subnet.

To add additional addresses, click on the “+” below the last field with an address. To subtract an address, click on the “X” next to the field you wish to delete.

  1. Disable/Enable Port Forwarding. If only the traffic for a specific port or port range is being forwarded, enable this setting.
  2. Select the Protocol from l TCP l UDP
  3. Configure the External Service Port. This is the port(s) on the external interface of the FortiGate (the destination port in the header of the packets). The first field is for the first port in the range the second is for the last port in the range. As you enter a value in the first field, the second field will auto populate with the same number, working on the premise that a single port is common. Just edit the second field to extend the range.
  4. Configure the setting Map to Port.This will be the listening port on the device located on the internal side of the network. It does not have to be the same as the External Service Port. The first field is for the first port in the range the second is for the last port in the range. As you enter a value in the first field, the second field will auto populate with the same number, working on the premise that a single port is common. Just edit the second field to extend the range.

Configuring a VIP for NAT64

In the Network section:

  1. Configure the External IP Address/Range.

There are two fields. If there is a single IP address, use that address in both fields. This will be the address on the outside of the network that is usually the public address of the server. Enter the address in the standard IPv6 format.

  1. Configure the Mapped IP Address/Range. This will be the address that the traffic is being directed to.

There are two fields. If there is a single IP address, use that address in both fields. Enter the address in the standard IPv4 format.

In the Optional Filters

  1. Disable/Enable the Optional Filters.

If only specific IP addresses and/or services are allowed to be the source for traffic using the VIP, enable the Optional Filters.

  1. To specify an allowed address enter the value in the field labeled Source Address. The value can be formatted in three different ways.

l Source IP – Use the standard format for a single IP address l Range – Enter the first and last members of the range l Subnet – Enter the IP address of the broadcast address for the subnet.

To add additional addresses, click on the “+” below the last field with an address. To subtract an address, click on the “X” next to the field you wish to delete.

  1. Disable/Enable Port Forwarding. If only the traffic for a specific port or port range is being forwarded, enable this setting.
  2. Select the Protocol from l TCP l UDP
  3. Configure the External Service Port. This is the port(s) on the external interface of the FortiGate (the destination port in the header of the packets). The first field is for the first port in the range the second is for the last port in the range. As you enter a value in the first field, the second field will auto populate with the same number, working on the premise that a single port is common. Just edit the second field to extend the range.
  4. Configure the setting Map to Port.This will be the listening port on the device located on the internal side of the network. It does not have to be the same as the External Service Port. The first field is for the first port in the range the second is for the last port in the range. As you enter a value in the first field, the second field will auto populate with the same number, working on the premise that a single port is common. Just edit the second field to extend the range.
  5. Press

Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!

Virtual IPs

Leave a reply

Virtual IPs

The mapping of a specific IP address to another specific IP address is usually referred to as Destination NAT.

When the Central NAT Table is not being used, FortiOS calls this a Virtual IP Address, sometimes referred to as a

VIP. FortiOS uses a DNAT or Virtual IP address to map an External IP address to an IP address. This address

does not have to be an individual host, it can also be an address range. This mapping can include all TCP/UDP ports or if Port Forwarding is enabled it will only refer to the specific ports configured. Because, the Central NAT table is disabled by default the term Virtual IP address or VIP will be used predominantly.

Virtual IP addresses are typically used to NAT external or Public IP addresses to internal or Private IP addresses. Using a Virtual IP address between 2 internal Interfaces made up of Private IP addresses is possible but there is rarely a reason to do so as the 2 networks can just use the IP addresses of the networks without the need for any address translation. Using a Virtual IP address for traffic going from the inside to the Internet is even less likely to be a requirement, but it is supported.

Something that needs to be considered when there are multiple Public IP addresses on the external interface(s) is that when a Virtual IP address is used without Port Forwarding enabled there is a reciprocal effect as far as traffic flow is concerned. Normally, on a firewall policy where NAT is enabled, for outgoing traffic the internal address is translated to the Public address that is assigned to the FortiGate, but if there is a Virtual IP address with no port forwarding enabled, then the Internal IP address in the Mapped field would be translated to the IP address configured as the External Address in the VIP settings.

Example

  • The assigned External address (WAN1) of the FortiGate unit is 172.12.96.3 with a subnet mask of 255.255.255.128 l There is a Virtual IP address set up to map the external address 172.12.96.127 on WAN1 to the internal IP address of 192.168.1.127
  • Port Forwarding is not enabled because you want all allowed traffic going to the external IP address to go to this server.

In this case any outbound traffic from 192.168.1.127 will go out on WAN1 with the IP address of 172.12.96.127 as the source IP address.

In terms of actually using the Virtual IP address, they would be using in the security policies in the same places that other addresses would be used, usually as a Destination Address.

UUID support for VIP

UUID is now supported in for virtual IPs and virtual IP groups. This includes virtual IPs for IPv4, IPv6, NAT46, and NAT64. To view the UUID for these objects in a FortiGate unit’s logs, log-uuid must be set to extended mode, rather than policy-only (which only shows the policy UUID in a traffic log). UUID can only be configured through the CLI

Syntax

config sys global set log-uuid {disable | policy-only | extended}

end

There is another type of address that the term “virtual IP address” commonly refers to which is used in load balancing and other similar configurations. In those cases, a number of devices share a separately created virtual IP address that can be sent to multiple possible devices. In FortiOS these are referred to as Virtual Servers and are configured in the “Load Balance” section.

If Central-NAT is enabled in the CLI the GUI will be different.

Instead of VIP Type, the field label will be DNAT & VIP Type

Instead of IPv4 the option will be IPv4 DNAT

There will also be the addition setting of Source Interface Filter.

Commands to set central-nat:

config system settings set central-nat [enable | disable] end


Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!

Creating an address group

Leave a reply

Creating an address group

  1. Go to Policy & Objects > Addresses.
  2. Select the down arrow next to Create New, select Address Group.
  3. Choose the Category, that is applicable to the proposed selection of addresses.
  4. Input a Group Name for the address object.

Depending on which Category has been chosen the configurations will differ slightly

IPv4 group
  1. Select the “+” in the Members You can select members of the group from the window that slides out from the left of the screen. It is possible to select more than 1 entry. Select the “X” icon in the field to remove an entry.
  2. Select the desired on/off toggle setting for Show in Address List.
  3. Select the desired on/off toggle setting for Static Route Configuration .
IPv6 group
  1. Select the “+” in the Members You can select members of the group from the window that slides out from the left of the screen. It is possible to select more than 1 entry. Select the “X” icon in the field to remove an entry.
  2. Select the desired on/off toggle setting for Show in Address List.
Proxy group
  1. Select which Type, either Source Group or Destination Group.
  2. Select the “+” in the Members You can select members of the group from the window that slides out from the left of the screen. It is possible to select more than 1 entry. Select the “X” icon in the field to remove an entry.
  3. Select the desired on/off toggle setting for Show in Address List.

Irrespective of the Category the groups all have the same final configuration options:

  1. Input any additional information in the Comments field.

2. Press OK. UUID support

Syntax:

config firewall {address|addres6|addgrp|addgrp6} edit 1 set uuid <example uuid: 8289ef80-f879-51e2-20dd-fa62c5c51f44> next end


Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!

Address groups

Leave a reply

Address groups

Address groups are designed for ease of use in the administration of the device. If you have a number of addresses or address ranges that will commonly be treated the same or require the same security policies, you can put them into address groups, rather than entering multiple individual addresses in each policy refers to them.

The use of groups is not required. If you have a number of different addresses you could add them individually to a policy and the FortiGate firewall will process them just as quickly and efficiently as if they were in a group, but the chances are that if you have used a group once you could need to use it again and depending on the number of addresses involved entering them individually for each policy can become tedious and the likelihood of an address being missed becomes greater. If you have a number of policies using that combination of addresses it is much easier to add or subtract addresses from the group than to try and remember all of the firewall policies that combination of addresses was used in. With the group, you only have to make the one edit and it is used by any firewall policy using that address group.

Because security policies require addresses with homogenous network interfaces, address groups should contain only addresses bound to the same network interface, or to Any.

For example, if address 1.1.1.1 is associated with port1, and address 2.2.2.2 is associated with port2, they cannot be in the same group. However, if 1.1.1.1 and 2.2.2.2 are configured with an interface of Any, they can be grouped, even if the addresses involve different networks. There are 3 Categories of Address groups to choose from:

l IPv4 Group l IPv6 Group l Proxy Group

You cannot mix different categories of addresses within a group, so whether or not it makes sense from an administrative purpose to group certain addresses together, if some are IPv4 and some are IPv6, it cannot be done.

 


Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!