SCTP

SCTP

As of FortiOS version 5.0, the FortiGate natively handles SCTP (Stream Control Transport Protocol) traffic, as an alternative to TCP and UDP for use in Carrier networks. The FortiGate handles SCTP as if it would any other traffic.

 

 

Overview

SCTP is a connection-oriented transport protocol that overcomes some of the limitations of both TCP and UDP that prevent reliable transfer of data over IP-based networks (such as those used by telephony systems and carrier networks). The ‘Stream’ in SCTP refers to the sequence of user messages or packets that are considered at the same time to be individual objects and also treated as a whole by networked systems. SCTP is less vulnerable to congestion and flooding due to more advanced error handling and flood protection built into the protocol.

 

SCTP features as compared to TCP and UDP  
Feature SCTP TCP UDP
 

State required at each endpoint

 

yes

 

yes

 

no

 

Reliable data transfer

 

yes

 

yes

 

no

 

Congestion control and avoidance

 

yes

 

yes

 

no

 

Message boundary conservation

 

yes

 

no

 

yes

 

Path MTU discovery and message fragmentation

 

yes

 

yes

 

no

 

Message bundling

 

yes

 

yes

 

no

 

Multi-homed hosts support

 

yes

 

no

 

no

 

Multi-stream support

 

yes

 

no

 

no

 

Unordered data delivery

 

yes

 

no

 

yes

 

Security cookie against SYN flood attack

 

yes

 

no

 

no

 

Built-in heartbeat (reachability check)

 

yes

 

no

 

N/A

All of these features are built into the design of the Protocol, and the structure of SCTP packets and networks. The FortiGate unit interprets the traffic and provides the necessary support for maintenance and verification features, but the features are not FortiGate specific. These features are documented in greater detail below.

 

State required at each endpoint

Constant back and forth acknowledgement and content verification messages are sent between all SCTP peer endpoints, and all endpoints’ state machine actions must be synchronized for traffic to flow.

 

Reliable data transfer

SCTP places data and control information (eg. source, destination, verification) into separate messages, both sharing the same header in the same SCTP packet. This allows for constant verification of the contained data at both ends and along the path, preventing data loss or fragmentation. As well, data is not sent in an interruptible stream as in TCP.

 

Congestion control and avoidance

Built-in, constantly updating path detection and monitoring automatically redirect packets along alternate paths in case of traffic congestion or inaccessible destinations. For deliberate/malicious congestion control, see the below section on Security cookie against SYN flood attack.

 

Message boundary conservation

SCTP is designed in such a way that no matter how messages are divided, redirected, or fragmented, the message boundaries will be maintained within the packets, and all messages cannot be appended without tripping verification mechanisms.

 

Path MTU discovery and message fragmentation

SCTP is capable of Path Maximum Transmission Unit discovery, as outlined in RFC4821. Two specific alterations have been made to how SCTP handles MTU. First, that endpoints will have separate MTU estimates for each possible multi-homed endpoint. Second, that bundled message fragments (as explained below) will be directed based on MTU calculations, so that retransmissions (if necessary) will be sent without delay to alternate addresses.

 

Message bundling

SCTP is a message-oriented protocol, which means that despite being a streaming data protocol, it transports a sequence of specific messages, rather than transporting a stream of bytes (like TCP). Since some data transmissions are small enough to not require a complete message’s worth of content, so multiple pieces of content will be transmitted simultaneously within the messages.

 

Multihomed hosts support

SCTP supports multi-homing, which is a network structure in which one or multiple sources/destinations has more than one IP address. SCTP can adapt to multi-homing scenarios and redirect traffic to alternate IP addresses in case of failure.

 

Multistream support

Due to the message bundling feature allowing for multiple pieces of content to be sent in messages at once, SCTP can ‘multi-stream’ content, by deliberately dividing it among messages at a fixed rate, so that multiple types of content (eg. both images and text) can be loaded at once, at the same pace.

 

Unordered data delivery

With control messages in every packet to provide verification of any packet’s data and its place in the stream, the data being transmitted can actually arrive in any order, and verify that all has arrived or that some is missing.


Having trouble configuring your Fortinet hardware or have some questions you need answered? Check Out The Fortinet Guru Youtube Channel! Want someone else to deal with it for you? Get some consulting from Fortinet GURU!

This entry was posted in FortiOS 5.4 Handbook on by .

About Mike

Michael Pruett, CISSP has a wide range of cyber-security and network engineering expertise. The plethora of vendors that resell hardware but have zero engineering knowledge resulting in the wrong hardware or configuration being deployed is a major pet peeve of Michael's. This site was started in an effort to spread information while providing the option of quality consulting services at a much lower price than Fortinet Professional Services. Owns PacketLlama.Com (Fortinet Hardware Sales) and Office Of The CISO, LLC (Cybersecurity consulting firm).

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.